Browsing by Subject "Fracing"
Now showing 1 - 5 of 5
- Results Per Page
- Sort Options
Item Development of a three-dimensional compositional hydraulic fracturing simulator for energized fluids(2013-08) Ribeiro, Lionel Herve Noel; Sharma, Mukul M.Current practices in energized treatments, using gases and foams, remain rudimentary in comparison to other fracturing fluid technologies. None of the available 3D fracturing models for incompressible water-based fluids have been able to capture the thermal and compositional effects that are important when using energized fluids, as their constitutive equations assume single-phase, single-component, incompressible fluid flow. These models introduce a bias in fluid selection because they do not accurately capture the unique behavior of energized fluids. The lack of modeling tools specifically suited for these fluids has hindered their design and field implementation. This work uses a fully compositional 3D fracturing model to answer some of the questions surrounding the design of energized treatments. The new model is capable of handling any multi-component mixture of fluids and chemicals. Changes in fluid density, composition, and temperature are predicted using an energy balance equation and an equation of state. A wellbore model, which relates the surface and bottomhole conditions, determines the pumping requirements. Fracture performance is assessed by a fractured well productivity model that accounts for damage in the invaded zone and finite fracture conductivity. The combination of the fracture, productivity, and wellbore models forms a standalone simulator that is suitable for designing and optimizing energized treatments. The simulator offers a wide range of capabilities, making it suitable for many different applications ranging from hydraulic fracturing to long-term injections for enhanced oil recovery, well clean-up, or carbon sequestration purposes. The model is applicable to any well configuration: vertical, deviated, or horizontal. The resolution of the full 3D elasticity problem enables us to propagate the fracture across multiple layers, where height growth is controlled by the vertical distribution of the minimum horizontal stress. We conducted several sensitivity studies to compare the fracture propagation, productivity, and pumping requirements of various fluid candidates in different reservoirs. The results show that good proppant placement and high fracture conductivities can be achieved with foams and gelled fluid formulations. Foams provide a wide range of viscosities without using excessive amounts of gelling agents. They also provide superior fluid-loss control, as the filter-cake is supplemented by the presence of gas bubbles that reduce liquid-flow into the porous medium. CO₂, LPG, and N₂ expand significantly (by 15% or more) as the reservoir heats the fluid inside the fracture. These fluids show virtually no damage in the invaded zone, which is a significant improvement upon water-based fluids in reservoirs that are prone to water blocking. These results, however, are contingent on an accurate fluid characterization supported by experimental data; therefore, our work advocates for complementary experimental studies on fluid rheology, proppant transport, and fluid leak-off. A comprehensive sensitivity study over a wide range of reservoir conditions identified five key reservoir parameters for fluid selection: relative permeability curve, initial gas saturation, reservoir pressure, changes to rock mechanical properties, and water-sensitivity. Because energized fluids provide similar rheology and leak-off behaviors as water-based fluids, the primary design question it to evaluate the extent of the damaged zone against costs, fluid availability, and/or safety hazards. If the fluid-induced damage is acceptable, water-based fluids constitute a simple and attractive solution; otherwise, energized fluids are recommended. Notably, energized fluids are well-suited for reservoirs that are depleted, under-saturated, and/or water-sensitive. These fluids are also favorable in areas with a limited water supply. As water resources become constrained in many areas, reducing the water footprint and the environmental impact is of paramount concern, thereby making the use of energized treatments particularly attractive to replace or subsidize water in the fracturing process.Item An examination of state regulations of hydraulic fracturing(2014-08) Perkins, Adam Reed; Olmstead, Sheila M.As hydraulic fracturing gains popularity in the energy industry, the state of Texas finds itself in a very advantageous position. With multiple regions which could have great potential for oil and natural gas extractable via the production technique, Texas has assumed a new importance for the energy industry. However, in order to fully utilize its advantages, the state of Texas should revise its oil and gas regulations, particularly with regard to groundwater use and contamination, air emissions, and discretion for municipal regulation of oil and gas operations, insofar as they may apply to hydraulic fracturing. This course of action only will this allow the state to efficiently utilize the production method while better balancing against the technique's risks.Item Investigating the utilization of surfactant in liquid unloading experiments of a propped fracture(2019-06-26) Mulkay, Connor Dixon; Sharma, Mukul M.The United States currently leads global production of oil and gas fundamentally in part due to its successful large shale plays. Advancements in technology and research have allowed the US to apply production techniques that increase recovery from these unconventional reservoirs; one of these principally being fracing. Through fracing, large fractures are created in the highly impermeable rock, thus increasing the amount of surface area for hydrocarbon flow and unlocking profitable production. After these fractures are created, the high amount of production only continues for a relatively short amount of time, after which production steeply slows down. Most companies react to this by drilling and fracing a new well in a different location. If these fractures could be improved so that the reduction in productivity is slowed down, companies would not have to drill as many well thereby saving money and causing less environmental disturbances. An idea to mitigate the productivity decline is by quickly unloading the built-up liquid in a newly created fracture. If suspended in a fluid for a period of time, gravitational forces cause proppant to settle in the lower part of the fracture. As the liquid slowly seeps into the formation, closure stresses from the surrounding rock begin to exceed pressure in the fracture and the upper part of the fracture closes off due to a lack of proppant. The surface area of the fracture promoting hydrocarbon flow is then drastically reduced. The closed off fracture could also potentially close off routes of flow if it is a critical pathway. A hypothesis is that if the built-up fluid in the fracture is unloaded quickly, the fracture will have a more homogenous distribution and will promote better fluid flow, thus slowing down the productivity decrease that is normally observed. Surfactants are already used for a variety of applications in the oil and gas industry. This thesis involves conducting experiments using surfactants to remove the built-up fluid in a fracture. Investigations are performed with different combinations of fluids typically used in industry. A fracture model made out of plastic plates is filled with proppant and a test fluid, and air is injected at the bottom of the fracture. The volume of liquid that exits the fracture is recorded as time passes. Results show that surfactant significantly improves the volume of unloaded liquid, even when in contact with oil at So = 30% in the fracture. Results from these experiments are not meant to be directly applied to the field, as experiments are not conducted at reservoir conditions. They are intended as a preliminary investigation into the potential of surfactant additives in hydraulic fracturing fluidItem Simulating refracturing treatments that employ diverting agents on horizontal wells(2013-08) Bryant, Stephen Andrew; Sharma, Mukul M.The use of hydraulic fracturing has increased rapidly and is now a necessary technique for the development of shale oil and gas resources. However, production rates from these plays typically exhibit high levels of decline. After one year, rates often decrease by over fifty percent. Refracturing – the process of hydraulically fracturing a well that has previously been fractured – is a proposed technique designed to offset these high decline rates and provide a sustainable increase in production. Benefits from refracturing can occur due to a variety of reasons, including the extension of fracture length, the increase in fracture conductivity or the reorientation of the fracture into new areas of the reservoir. In this thesis, the simulation of refracturing treatments on horizontal wells with the use of a diverting agent is described. Diverting agents are used to distribute flow more evenly along the wellbore and to replace the use of costly downhole equipment employed to isolate sections of the wellbore. When diverting agent is deposited, a cake forms with an associated permeability. Flow is diverted from the fractures with high amounts of diverting agent because the larger cake results in a greater resistance to flow. The diverting agent cake breaks down with time at reservoir temperature so that production is uninhibited. Two different models are used to account for the application of diverting agent. One assumes the diverting agent cake forms in the perforation tunnel and the other assumes it forms in the fracture. The propagation of competing fractures is calculated using a computer code developed at the University of Texas called UTWID. In both models, the simulations showed successful diversion of flow. Previously understimulated fractures – that is, shorter fractures or fractures that would grow less preferentially under normal fracturing treatments – grew at a faster pace after pumping of the diverting agent. A sensitivity analysis was conducted on several of the key refracturing design parameters, and the interdependence of the parameters was demonstrated. The simulations support the concept that diverting agents can be used to more evenly stimulate the entire length of the lateral.Item Study on the feasibility of using electromagnetic methods for fracture diagnostics(2012-08) Saliés, Natália Gastão; Sharma, Mukul M.; Ling, HaoThis thesis explores two ways of developing a fracture diagnostics tool capable of estimating hydraulic fracture propped length and orientation. Both approaches make use of an electrically conductive proppant. The fabrication of an electrically conductive proppant is believed to be possible and an option currently on the market is calcined petroleum coke. The first approach for tool development was based on principles of antenna resonance whereas the second approach was based on low frequency magnetic induction. The former approach had limited success due to the lack of resonant features at the stipulated operating conditions. Low frequency induction is a more promising approach as electromagnetic fields showed measurable changes that were dependent on fracture length in simulations. The operation of a logging tool was simulated and the data showed differences in the magnetic field magnitude ranging from 2% to 107% between fracture sizes of 20m, 50m, 80m, and 100m. Continuing research of the topic should focus not only on simulating more diverse fracture scenarios but also on developing an inversion scheme necessary for interpreting field data.