Modeling the Effects of Capillary Pressure and the Manipulation of Viscous to Capillary Forces to Recover Residual Saturation Using the Pore N-Let Model

Simple item page
dc.contributor.advisorLake, Larry W.
dc.creatorKrishnan, Rahul
dc.date.accessioned2020-04-21T22:39:06Z
dc.date.available2020-04-21T22:39:06Z
dc.date.issued2008-08
dc.description.abstractThe difficulty in recovering residual oil is created by (1) the reservoir pore geometry (length, number, and size of tubes and throats), (2) the fluid properties and interfaces, (3) viscous and capillary forces acting on the fluids, and (4) reservoir heterogeneity. This research is intended to expand the pore doublet model and use it to model flow in reservoirs. By first modeling scenarios of simple flow, a better idea of the nature of the pore doublet is gathered. Then the model is expanded to a pore n-let and used with experimental data on mercury injection with the intent of applying it to reservoir models. Further experiments are done with field data taken from the San Juan and Greensburg fields and the following conclusions are made. Capillary forces govern flow in small tubes while viscous forces govern flow in large tubes. Over a distribution of small and large tubes, increasing capillary number will cause larger tubes to flow faster and trap oil in smaller tubes quicker. A strong assumption is made that only large pores will trap oil, and small tubes will displace oil. This assumption leads to complete displacement of the trapped oil over a range of increasing capillary number. Capillary desaturation curves are produced from these calculations and qualitatively agree with curves produced in other work. Results show that displacing residual oil is heavily dependent on pore geometry and pore size distribution. Well sorted distributions caused low initial non-wetting residual saturation, but larger pores required a higher capillary number to remove trapped oil. In most cases, complete desaturation typically occurred over capillary number range of one order of magnitude. These experiments and conclusions are discussed in detail.en_US
dc.description.departmentPetroleum and Geosystems Engineeringen_US
dc.format.mediumelectronicen_US
dc.identifier.urihttps://hdl.handle.net/2152/80771
dc.identifier.urihttp://dx.doi.org/10.26153/tsw/7786
dc.language.isoengen_US
dc.relation.ispartofUT Electronic Theses and Dissertationsen_US
dc.rightsCopyright © is held by the author. Presentation of this material on the Libraries' web site by University Libraries, The University of Texas at Austin was made possible under a limited license grant from the author who has retained all copyrights in the works.en_US
dc.rights.restrictionRestricteden_US
dc.subjectCapillaryen_US
dc.subjectViscousen_US
dc.titleModeling the Effects of Capillary Pressure and the Manipulation of Viscous to Capillary Forces to Recover Residual Saturation Using the Pore N-Let Modelen_US
dc.typeThesisen_US
dc.type.genreThesisen_US
thesis.degree.departmentPetroleum and Geosystems Engineeringen_US
thesis.degree.disciplinePetroleum Engineeringen_US
thesis.degree.grantorUniversity of Texas at Austinen_US
thesis.degree.levelMastersen_US
thesis.degree.nameMasters of Science in Engineeringen_US

Access full-text files

Original bundle

Now showing 1 - 1 of 1
No Thumbnail Available
Name:
Thesis.2008.Krishnan_Rahul.pdf
Size:
2.11 MB
Format:
Adobe Portable Document Format
Description:
Restricted to UT Austin EID holders
Download

License bundle

Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
1.64 KB
Format:
Item-specific license agreed upon to submission
Description:
Download

Collections

UT Electronic Theses and Dissertations