Browsing by Subject "Permeability anisotropy"
Now showing 1 - 2 of 2
- Results Per Page
- Sort Options
Item Geologically-based permeability anisotropy estimates for tidally-influenced reservoir analogs using lidar-derived, quantitative shale character data(2011-05) Burton, Darrin; Wood, Lesli J.; Steel, Ronald; Mohrig, David; Kim, Wonsuck; Hesse, Marc; Janson, XavierThe principle source of heterogeneity affecting flow behavior in conventional clastic reservoirs is discontinuous, low-permeability mudstone beds and laminae (shales). Simple ‘streamline’ models have been developed which relate permeability anisotropy (kv/kh ) at the reservoir scale to shale geometry, fraction, and vertical frequency. A limitation of these models, especially for tidally-influenced reservoirs, is the lack of quantitative geologic inputs. While qualitative models exist that predict shale character in tidally-influenced environments (with the largest shales being deposited near the turbidity maximum in estuaries, and in the prodelta-delta front), little quantitative shale character data is available. The purpose of this dissertation is to collect quantitative data to test hypothetical relationships between depositional environment and shale character and to use this data to make geologically-based estimates of for different reservoir elements. For this study, high-resolution, lidar point-clouds were used to measure shale length, thickness, and frequency. This dissertation reports a novel method for using distance-corrected lidar intensity returns to distinguish sandstone and mudstone lithology. Lidar spectral and spatial data, photo panels, and outcrop measurements were used to map and quantify shale character. Detailed shale characteristics were measured from four different tidally-influenced reservoir analogs: estuarine point bar (McMurray Formation, Alberta, Canada), tidal sand ridge (Tocito Sandstone, New Mexico), and unconfined and confined tidal bars (Sego Sandstone, Utah). Estuarine point bars have long (l=67.8 m) shales that are thick and frequent relative to the other units. Tidal sand ridges have short (l=8.6 m dip orientation) shales that are thin and frequent. Confined tidal bars contain shales that are thin, infrequent, and anisotropic, averaging 16.3 m in length (dip orientation). Unconfined tidal bars contain nearly equidimensional (l=18.6 m dip orientation) shales with moderate thicknesses and vertical frequency. The observed shale geometries agree well with conceptual models for tidal environments. The unique shale character of each unit results in a different distribution of estimated . The average estimated kv/kh values for each reservoir element are: 8.2*10^4 for estuarine point bars, 0.038 for confined tidal bars, 0.004 for unconfined tidal bars, and 0.011 for tidal sand ridges.Item Mechanical, failure and flow properties of sands : micro-mechanical models(2011-05) Manchanda, Ripudaman; Olson, Jon E.; Sharma, Mukul M.This work explains the effect of failure on permeability anisotropy and dilation in sands. Shear failure is widely observed in field operations. There is incomplete understanding of the influence of shear failure in sand formations. Shear plane orientations are dependent on the stress anisotropy and that view is confirmed in this research. The effect of shear failure on the permeability is confirmed and calculated. Description of permeability anisotropy due to shear failure has also been discussed. In this work, three-dimensional discrete element modeling is used to model the behavior of uncemented and weakly cemented sand samples. Mechanical deformation data from experiments conducted on sand samples is used to calibrate the properties of the spherical particles in the simulations. Orientation of the failure planes (due to mechanical deformation) is analyzed both in an axi-symmetric stress regime (cylindrical specimen) and a non-axi-symmetric stress regime (right cuboidal specimen). Pore network fluid flow simulations are conducted before and after mechanical deformation to observe the effect of failure and stress anisotropy on the permeability and dilation of the granular specimen. A rolling resistance strategy is applied in the simulations, incorporating the stiffness of the specimens due to particle angularity, aiding in the calibration of the simulated samples against experimental data to derive optimum granular scale elastic and friction properties. A flexible membrane algorithm is applied on the lateral boundary of the simulation samples to implement the effect of a rubber/latex jacket. The effect of particle size distribution, stress anisotropy, and confining pressure on failure, permeability and dilation is studied. Using the calibrated micro-properties, simulations are extended to non-cylindrical specimen geometries to simulate field-like anisotropic stress regimes. The shear failure plane alignment is observed to be parallel to the maximum horizontal stress plane. Pore network fluid flow simulations confirm the increase in permeability due to shear failure and show a significantly greater permeability increase in the maximum horizontal stress direction. Using the flow simulations, anisotropy in the permeability field is observed by plotting the permeability ellipsoid. Samples with a small value of inter-granular cohesion depict greater shear failure, larger permeability increase and a greater permeability anisotropy than samples with a larger value of inter-granular cohesion. This is estimated by the number of micro-cracks observed.